ZV36SSJSSMONOGRAM 36" STAINLESS STEEL PROFESSIONAL HOOD
Listed by
Underwriters
Laboratories
Product Specification Revised 1/18
ADVANCED PLANNING
DUCTWORK PLANNING
• These vent hoods are equipped for 10" round ductwork. In
most instances they may be transitioned to 8" round.
• This hood may be vented vertically through upper cabinets,
sot or ceiling. A duct transition piece is supplied for
vertical exhaust. Use locally supplied elbows to vent
horizontally through the rear wall.
• Determine the exact location of the vent hood.
• Plan the route for venting exhaust to the outdoors.
• Use the shortest and straightest duct route possible. For
satisfactory performance, duct run should not exceed
150 ft. equivalent length for any duct congurations.
• Refer to “Duct Fittings” chart to compute the maximum
permissible length for duct runs to the outdoors.
• Use metal ductwork only.
• Install a wall cap or roof cap with damper at the exterior
opening. Order the wall or roof cap and any transition
needed in advance.
WALL FRAMING FOR ADEQUATE SUPPORT
• These vent hoods are heavy. Adequate structural support
must be provided. Hoods must be secured to vertical studs
in the wall.
• It is strongly recommended that the vent hood with duct
cover be on site before nal framing and wall nishing.
This will also help to accurately locate the ductwork and
electrical service.
DECORATIVE DUCT COVERS
Decorative duct covers, 6" and 12" high, are available to t
all models. The duct cover conceals the ductwork running
from the top of the hood to the ceiling or sot. Stack one
or more duct covers over the top of the hood to reach
your ceiling height.
6" DUCT COVERS
HOOD MODEL 6" DUCT COVER DIMENSIONS
ZV36SSJSS ZX36DC6J 6"H x 15-3/4"W x
11-7/8"D
12" DUCT COVERS
HOOD MODEL 12" DUCT COVER DIMENSIONS
ZV36SSJSS ZX36DC12J 12"H x 15-3/4"W x
11-7/8"D
OPTIONAL DUCT COVER ACCESSORIES
Decorative duct covers are available in 6" and 12"
heights. Duct covers may be stacked, in various
combinations, to conceal the ductwork running from
the top of the hood to the ceiling.
• Before you begin, you should determine the
installation height of the hood
and order the correct size duct
cover. The duct covers should be
ordered at the same time as the
vent hood and be on site before
installation. Order the duct cover
corresponding to your model.
Optional Duct Cover Accessories
6" Duct Cover
12" Duct Cover
POWER SUPPLY
IMPORTANT – (PLEASE READ CAREFULLY)
WARNING
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before
beginning installation.
Do not use an extension cord or adapter plug with this
appliance. Follow national electrical codes or prevailing
local codes and ordinances.
ELECTRIC SUPPLY
These vent hoods must be supplied with 120V, 60Hz, and
connected to an individual, properly grounded branch
circuit, and protected by a 15 or 20 amp circuit breaker or
time delay fuse.
• Wiring must be 2 wire with ground.
• If the electrical supply does not meet the above
requirements, call a licensed electrician before proceeding.
• Route house wiring as close to the installation location as
possible on the back wall or ceiling.
• Connect the wiring to the house wiring in accordance with
local codes.
GROUNDING INSTRUCTIONS
The grounding conductor must be connected to a ground
metal, permanent wiring system, or an equipment-grounded
terminal or lead on the hood.
WARNING
The improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with
a qualied electrician or service representative if you are in
doubt whether the appliance is properly grounded.
(3 pages)
(16 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals