InstallationInstructions31-49078-1 224D2601P003 04-15 GE36” Built-In All-Refrigerators and All-Freezersmonogram.com
10SIDE PANELSSide panels must be used whenever the sides of the unit will be exposed. The 1/4” side panels will slip into the side case trim. Secure t
Design Guide - Standard Installation11Top View130° DOOR SWINGScale 1:1Frameless Cabinets: The case trim overlaps cabinets at the top and sides.Theref
Installation Instructions - Standard Installation12HARDWARE SUPPLIED• Water filter bypass plug• Anti-Tip brackets• 3 lag screws• 2 Hair Pin Cotters• 4
Installation Instructions - Standard Installation13STEP 3 INSTALL SIDE PANELSSkip this step when not using side panelsIf you are using 1/4” side pane
• The anti-tip wall bracket has a series of holes. Select 2 holes that match with the located studs. Make sure the holes selected are on the center of
Install Screws and Bolts:• Have someone hold the wall bracket centered in place with each of the holes aligned with the correct opening in the bracket
Installation Instructions - Standard Installation16Remove Grilles for Access to Anti-Tip Locking HooksFresh Food Unit• Open the access door.• Remove t
17Installation Instructions - Standard Installation STEP 5 LEVEL UNITAll models have 4-point leveling. The front is supported by leveling legs; the r
Installation Instructions - Standard Installation18 STEP 7 ADJUST DOOR SWINGNOTE: This appliance has a 3-position door stop. When space does not allo
Installation Instructions - Standard Installation19 STEP 9 INSTALL FRAMED PANELS• There are two sets of holes in the handle side trim. Replace the h
2Safety InformationBEFORE YOU BEGIN Read these instructions completely and carefully.• IMPORTANT – Save these instructions for local inspector’s use.
Installation Instructions - Standard Installation20 STEP 9A INSTALL OVERLAY PANELS• There are two sets of holes in the handle side trim. Replace the
STEP 10 CONNECT WATER SUPPLY (FREEZER MODELS ONLY)• Locate and bring the tubing to the front of the cabinet.• Turn the water on to flush debris fro
Instructions for Flush Installation22
Design Guide - Flush Installation2338-3/4" Frame to Frame Width*84" FromFloor toTop Frame35"Case Width*83-1/2" atRear25-3/8"
Design Guide - Flush InstallationThese units are equipped with a 3-position door stop. The factory set 115° door swing can be adjusted to 90° if clear
25Design Guide - Flush Installation 1/2” OVERLAY PANEL DIMENSIONSFor a more custom appearance, overlay panels may be installed on trimmed models. The
Design Guide - Flush Installation263/4” DECORATIVE PANEL DIMENSIONSFor a more custom appearance, overlay panels may be installed to give a flush appea
27Design Guide - Flush Installation3/4” RAISED DOOR PANEL ROUTINGFor 3/4” raised door panel, routing is required. The router depth is 1/4” all the way
28Design Guide - Flush Installation3/4” RAISED GRILLE PANEL ROUTINGFor 3/4” raised grille panel, routing is required. The router depth is 1/4” all the
29SIDE PANELSSide panels must be used whenever the sides of the unit will be exposed. The 1/4” side panels will slip into the side case trim. Secure t
CONSIGNES DE SÉCURITÉ Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures o
Installation Instructions - Flush Installation30HARDWARE SUPPLIED• Water filter bypass plug• Anti-Tip brackets• 3 lag screws• 2 Hair Pin Cotters• 4 wa
Installation Instructions - Flush Installation31STEP 3 INSTALL SIDE PANELSSkip this step when not using side panelsIf you are using 1/4” side panels,
Installation Instructions - Flush Installation32 STEP 4 INSTALL CASE TRIMThe unit arrives with case trim for standard installation attached. Flush in
• Mark an additional hole at each end of the bracket. If one of the studs is closer to the end of the bracket, mark an additional hole towards the cen
Installation Instructions - Flush Installation34Remove Grilles for Access to Anti-Tip Locking HooksFresh Food Unit• Open the access door.• Remove the
STEP 7 ADJUST DOOR SWINGNOTE: This appliance has a 3-position door stop. When space does not allow the door to swing open fully to 115°, you may cha
Custom Handles• Custom handles must be used for flush installation. The handle must be properly secured to the overlay panel before sliding the panel
Installation Instructions - Flush Installation STEP 10 CONNECT WATER SUPPLY (FREEZER MODELS ONLY)• Locate and bring the tubing to the front of the c
Instructions for Stainless Steel Installation38
Design Guide - Stainless Steel Installation3936" Frame to Frame Width*84" FromFloor toTop Frame35"Case Width*83-1/2" atRear25-3/8&
Contents4Safety 2, 3Instructions for Standard Installation 5-21Planning GuideThe Installation Space 6Dimensions and Clearances 6-7Customization Bas
Design Guide - Stainless Steel Installation40These units are equipped with a 3-position door stop. The factory set 115° door swing can be adjusted to
41Design Guide - Stainless Steel InstallationCUSTOMIZATION BASICS: Custom Handles and Accessory KitsProfessional Style Stainless Steel ModelsStainless
Design Guide - Stainless Steel Installation42Top View130° DOOR SWINGScale 1:1Frameless Cabinets: The case trim overlaps cabinets at the top and sides
Installation Instructions - Stainless Steel Installation43HARDWARE SUPPLIED• Water filter bypass plug• Anti-Tip brackets• 3 lag screws• 2 Hair Pin Cot
Installation Instructions - Stainless Steel Installation44STEP 3 INSTALL SIDE PANELSSkip this step when not using side panelsIf you are using 1/4” si
• The kit supplied with the unit contains 2 lag bolts and 4 toggles with bolts. The wall bracket will be attached to the wall in 4 places.• Measure th
• Gently pull back at the ends of the plastic straps to make the channel rest flush behind the wall.• Hold the ends of the straps in one hand and slid
Installation Instructions - Stainless Steel Installation47Move Unit into Final Position• Move appliance toward its final installed location. Align the
48Installation Instructions - Stainless Steel Installation STEP 6 SECURE UNIT TO WALL• The “L” rods can be found in the upper left and right corners
49 STEP 8 CONNECT WATER SUPPLY (FREEZER MODELS ONLY)• Locate and bring the tubing to the front of the cabinet.• Turn the water on to flush debris fr
Instructions for Standard Installation5
50Notes
51Notes
Printed in the United StatesNOTE: While performing installations described in this book, safety glasses or goggles should be worn.For Monogram® local
Design Guide - Standard Installation36" Frame to Frame Width*84" FromFloor toTop Frame35"Case Width*83-1/2" atRear25-3/8" Cas
Design Guide - Standard Installation7These units are equipped with a 3-position door stop. The factory set 115° door swing can be adjusted to 90° or 1
Design Guide - Standard Installation8CUSTOMIZATION BASICS: Framed or Overlay Panels, Custom Handles and Accessory KitsTrimmed models are designed to b
Design Guide - Standard Installation9If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the
Comments to this Manuals